Difference between revisions of "CodeChart:HP 2648A/HP 2648 Mode"

From Terminals
Jump to: navigation, search
(create page)
 
 
(21 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[:Special:PrefixIndex/{{FULLPAGENAME}}/|Subpages of {{SUBPAGENAME}}]]
 
[[:Special:PrefixIndex/{{FULLPAGENAME}}/|Subpages of {{SUBPAGENAME}}]]
  
{| border="1" style="text-align: center;"
+
{|
! style="width: 3em;" |   !! style="width: 3em;" | 0 !! style="width: 3em;" | 1
+
| valign="top" |
! style="width: 3em;" | 2 !! style="width: 3em;" | 3 !! style="width: 3em;" | 4
+
{{CodeChart
! style="width: 3em;" | 5 !! style="width: 3em;" | 6 !! style="width: 3em;" | 7
+
| title=Received
 +
| bel=#bel
 +
| so=#so
 +
| si=#si
 +
| esc=/ESC
 +
}}
 +
| style="width: 2ex;" |
 +
| valign="top" |
 +
{{CodeChart
 +
| title=Transmitted
 +
| f=#f
 +
| s=#s
 +
| u=#u
 +
| esc=/ESC
 +
}}
 
|-
 
|-
! 0
+
| valign="top" |
| NUL || DLE || SP || 0 || @ || P || ` || p
+
{| class="wikitable"
|-
+
|+ Control Sequences
! 1
+
{{CodeDescriptionHeader}}
| SOH || DC1 || !  || 1 || A || Q || a || q
+
{{CodeDescriptionRow|BEL|bel|Bell}}
|-
+
{{CodeDescriptionRow|SO|so|Switch to Alternate Character Set}}
! 2
+
{{CodeDescriptionRow|SI|si|Switch to Standard Character Set}}
| STX || DC2 || " || 2 || B || R || b || r
+
|}
|-
+
|
! 3
+
| valign="top" |
| ETX || DC3 || #  || 3 || C || S || c || s
+
{| class="wikitable"
|-
+
|+ Control Sequences
! 4
+
{{CodeDescriptionHeader}}
| EOT || DC4 || $  || 4 || D || T || d || t
+
{{CodeDescriptionRow|F|f|Device Operation Failed}}
|-
+
{{CodeDescriptionRow|S|s|Device Operation Succeeded}}
! 5
+
{{CodeDescriptionRow|U|u|Device Operation Interrupted by User}}
| ENQ || NAQ || %  || 5 || E || U || e || u
+
|}
|-
+
 
! 6
 
| ACK || SYN || &  || 6 || F || V || f || v
 
|-
 
! 7
 
| BEL || ETB || '  || 7 || G || W || g || w
 
|-
 
! 8
 
| BS  || CAN || (  || 8 || H || X || h || x
 
|-
 
! 9
 
| HT  || EM  || )  || 9 || I || Y || i || y
 
|-
 
! 10
 
| LF  || SUB || *  || : || J || Z || j || z
 
|-
 
! 11
 
| VT || [[{{FULLPAGENAME}}/ESC|'''ESC''']] || + || ; || K || [ || k || {
 
|-
 
! 12
 
| FF || IS4 || , || < || L || \ || l || |
 
|-
 
! 13
 
| CR || IS3 || - || = || M || ] || m || }
 
|-
 
! 14
 
| SO || IS2 || . || > || N || ^ || n || ~
 
|-
 
! 15
 
| SI || IS1 || / || ? || O || _ || o || DEL
 
 
|}
 
|}
 +
 +
== Parameters ==
 +
 +
Some control sequences take one or more parameters.  While ANSI control sequences place the parameter between the control sequence inducer (ESC [) and the final character of the sequence, HP 2648A control sequences place parameters following the final character defining the command.
 +
 +
Each parameter consists of a digit sequence followed by a letter.  For control sequences that take multiple parameters, all but the last parameter will have a lower case letter and the last parameter will have an upper case letter to terminate the parameter sequence.

Latest revision as of 17:17, 15 February 2013

Subpages of HP 2648 Mode

Received
0 1 2 3 4 5 6 7
0 NUL DLE SP 0 @ P ` p
1 SOH DC1 ! 1 A Q a q
2 STX DC2 " 2 B R b r
3 ETX DC3 # 3 C S c s
4 EOT DC4 $ 4 D T d t
5 ENQ NAQ % 5 E U e u
6 ACK SYN & 6 F V f v
7 BEL ETB ' 7 G W g w
8 BS CAN ( 8 H X h x
9 HT EM ) 9 I Y i y
10 LF SUB * : J Z j z
11 VT ESC + ; K [ k {
12 FF IS4 , < L \ l |
13 CR IS3 - = M ] m }
14 SO IS2 . > N ^ n ~
15 SI IS1 / ? O _ o DEL
Transmitted
0 1 2 3 4 5 6 7
0 NUL DLE SP 0 @ P ` p
1 SOH DC1 ! 1 A Q a q
2 STX DC2 " 2 B R b r
3 ETX DC3 # 3 C S c s
4 EOT DC4 $ 4 D T d t
5 ENQ NAQ % 5 E U e u
6 ACK SYN & 6 F V f v
7 BEL ETB ' 7 G W g w
8 BS CAN ( 8 H X h x
9 HT EM ) 9 I Y i y
10 LF SUB * : J Z j z
11 VT ESC + ; K [ k {
12 FF IS4 , < L \ l |
13 CR IS3 - = M ] m }
14 SO IS2 . > N ^ n ~
15 SI IS1 / ? O _ o DEL
Control Sequences
Prefix Description Parameters
BEL Bell none
SO Switch to Alternate Character Set none
SI Switch to Standard Character Set none
Control Sequences
Prefix Description Parameters
F Device Operation Failed none
S Device Operation Succeeded none
U Device Operation Interrupted by User none

Parameters

Some control sequences take one or more parameters. While ANSI control sequences place the parameter between the control sequence inducer (ESC [) and the final character of the sequence, HP 2648A control sequences place parameters following the final character defining the command.

Each parameter consists of a digit sequence followed by a letter. For control sequences that take multiple parameters, all but the last parameter will have a lower case letter and the last parameter will have an upper case letter to terminate the parameter sequence.